The h11 bolt (wmc7 and wmc6) is a high quality, aircraft standard fastener. Under racing conditions, we suggest that the h11 bolts be changed periodically.
All bolts should be lubricated under the heads as well as on the threads. We recommend the bolt lube supplied with the rods, or as an alternative, a molybdenum base paste mixed with engine oil.
The preferred method to torque the bolt is by using the stretch figure 60,75 nm (3/8 sps - wmc6 9,65mm).


Fitment:
Gt2 (01-05) / turbo (01-05) / GT2 (96-98) / turbo (95-98) / cup-race (94-98) / rsr (96-97) / rs (95-96) /
C4s (96-98) / c4 (95-98) / c2s (96-98) / c2 (94-98) / 968cs (93-95) / 968 (92-95) / turbo 3.6 (93-94) / turbo 3.3 (91-92) / cup-race (90-93) ...(choose a part on the right to read more)

General Fitment

Connecting rod with plc carr-6 screw. The s connecting screw (plc carr-6) needs only every third time to be changed under race conditions or motor sport use when overhauling the engine. When used in 997.1turbo connecting rod bearing 99310314715set must be used (tongue / nose opposite). Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then sho...(choose a part on the right to read more)

Carrillo is one of the most respected connecting rod manufacturers in competitive motorsports. Carrillo rods are constructed from their proprietary alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then shot-peened to achieve the ultimate in strength and fatigue properties. The carrillo multiphase (carr) connecting rod bolt (sps-carr-6) is a high quality, aircraft standard fastener. Each bolt is manufactured with asymmetrical threads, each thread has a slightly different design than the ...(choose a part on the right to read more)

High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 12 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Cp-carrillo's fastener assembly lube is molybdenum based lubrication grease with enhanced properties. This product offers an improved clamp load repeatability, greater resistance to high pressure and temperature (range -22f to 1200f), and no oil contamination. The coefficient of friction stays unchanged, even after several connecting rod bolt re-tightening and loosening processes. We highly recommend lubricating the connecting rod bolt head and thread with this lubricant. Be sure to add it to your order if you are replacing your rod bolts. Sold individually.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or req...(choose a part on the right to read more)

This is a high-quality replacement for original number, 911 211 022 10 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car.

This item may need to be sourced from ge...(choose a part on the right to read more)

This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the left side reduces the ...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport ...(choose a part on the right to read more)

Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Tig welded. Semi-gloss black finish. Please note: these bars are hand made to order. They typically take between 4-16 weeks. Every heigo bar or cage is considered a motorsport part and is a special-order item. Moto...(choose a part on the right to read more)

Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)

Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)

The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.

With our single can muffler and 200cell high flow cats installed to the stock huge oval tips, we strapped our 2010 pdk to the dyno. The exhaust made a peak increase in standard mode of 15awhp and 23f...(choose a part on the right to read more)

With over 25+ years of Porsche air and water-cooled experience, fabspeed motorsport usa offers a great enhancement for your stock exhaust or aftermarket exhaust on your Porsche 992 Carrera. Using only the highest quality helical valves imported directly from the u.k., our system eliminates any risk of failing exhaust valves. Helical limited in great britain supplies the world's very best exhaust valves to Porsche, ferrari, lamborghini, mclaren, aston martin, and other hypercar manufacturers. Other cheap aftermarket exhaust valves are not able to handle the heat produced by a rear or mid-engine car and are guaranteed to fail, break and rattle. Helical u.k. Imported exhaust valves are bullet-proof and never fai...(choose a part on the right to read more)

The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
Features
• delivers deep aggressive exhaust sound
• significant weight reduction of 40 pounds
• 304 stainless steel aerospace tubing
• meticulo...(choose a part on the right to read more)

Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
Left & right hand threaded rodends allow for easy length adjustment to eliminate swaybar preload.

Correctly sized, precision, teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. no wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends.

Eliminates the factory compliant rubber drop link bushings for improved swaybar response.
Precisely connects the stock swaybar to the front suspension arm.

This is a high-quality replacement for original number, 911 211 021 60 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Black paint finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold al...(choose a part on the right to read more)

This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the right side re...(choose a part on the right to read more)

This is a high-quality replacement for original number, 911 211 021 14 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911101 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)

Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs i...(choose a part on the right to read more)

Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness bar, part...(choose a part on the right to read more)

Rost off extra is fortified with ptfe and has many uses such as lubricating locks, hinges, moving parts, freeing nuts and bolts, stopping and preventing corrosion. This product saves production, maintenance and repair time. It is ideally suited for refrigeration equipment, automobiles, workshops, airplanes, boats, etc. Contains no ozone depleters.

General Fitment

The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)

This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8 bolts, allowing for a full 360 degree motion of the motor. Bolts up to every Porsche engine ever produced. Machined with all the necessary reliefs and/or notches to allow for clearance of all engine parts including the flywheel and its respective lock tool.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.